Replacement Test Equipment Cables
Prices effective 17 MARCH 2017
|Quick Links: Capacitance Meter (home) Test Equipment (home) About Us and Quality Ordering and Shipping Contact Us Useful Links|
Search by Instrument Model or Cable Part Number
Hewlett Packard / Agilent Instrument
89441A / 89431A
89410A / 89430A
11764A / 11713A
Multiport Test Sets
85301A 85301B 85301C
Hewlett Packard / Agilent Cable
70800A B C
Rohde & Schwarz
5725A 859897 or 842901
Wiltron / Anritsu
MS9030A - MS9701B
4-Wire PWM Fan
Recent Additions to Our Line of Interconnect Cables -
We have a few cables that are used to connect the HP 432A/B power meters to the thermistor sensor. These are used OEM cables, but they have been cleaned and fully tested on OEM equipment. They may have a few nicks and scratches, but are fully functional cables. Current Keysight price is $661. Length is 5 ft.
Front panel ALC (3-pin) and rear AUX interface cables for HP / Agilent EMI receiver.
This adapter connects the HP 85105A test set to the 85104A millimeter wave test set.
This cable connects the Antrisu optical spectrum analyzer MS9030A display unit to the MS9701B optical unit. Standard length is 24 inches.
This cable is for use with the 89441A Vector Signal Analyzer System. It connects serial port 2 on the display unit to serial port 2 on the RF unit. The cable is compatible with HP / Agilent instruments 89431A, 89441V, 89440A, 89410A, 89430A, and E3238N-431 (standard length 18 inches) and includes inline EMI suppressors. NOTE: This cable has metric jack screws.
Fully Guarded Interface Cable for the Fluke 5205A Amplifier to 5700A / 5720A Series II Calibrators (standard length 48 inches).
Fully Guarded Interface Cable for the Fluke 5220A Amplifier to 5700A / 5720A Series II Calibrators (standard length 48 inches).
4 Pin Female PWM to 4 Pin Male PWM Extension Cable. Special order item. This extension cable connects a 4-pin PW-controlled fan to a 4-pin header on a motherboard or fan controller board. These cables are made to order in custom lengths only and are available with or without protective sheath. Orders for small quantities can usually be filled in 10-15 business days. Price upon request. Please inquire. To order, specify P/N, length -xx (inches), and quantity:
For use with Agilent / HP multiport test sets such as the 87030A, 87050A, 87050E, 87075C, Z5623A, Z5623AK66, etc. (standard length 20 inches, 0.5 meter).
87421A power supply to 87415A microwave amplifier cable (standard length 80 inches, 2 meter). NOTE: This cable is also used with the following Agilent microwave preamplifiers 83006A, 83017A, 83018A, 83050A, and 83051A, and with the Agilent 87422A power supply.
RF Plug-in 64-pin Microribbon I/O Extender Cable (standard length 40 inches, 1 meter).
RF Plug-in Power Supply Extender Cable (standard length 40 inches, 1meter).
Signal and Control interconnect cables are for use with the Wiltron 360B Vector Network Analyzer system. Standard length is 32 inches.
This cable is for use with the HP Agilent 11713A attenuator / switch driver and 84904, 84906, 84907-series programmable step attenuators. Standard lengths are 5 feet (-5), 10 feet (-10), or 15 feet (-15). Custom length cables are available upon request (see below).
Color coding for easy cable identification is available upon request.
The cost of a custom length cable is $3.00 per foot plus the base price of $79.00. Specify cable part number as 11764-60004-xx-color, where xx is length in feet, and choose from the available label colors: RED, BLUE, YELLOW, GREEN, WHITE, BLACK, or none (leave blank).
Interconnect cable for the 16058A test fixture and the HP 4145A or 4145B Semiconductor Parameter Analyzer. Standard length is 5 feet. Custom length cables are available upon request.
4145A or 4145B Shorting Plug
Shorting Plug for the HP 4145A or 4145B Semiconductor Parameter Analyzer.
11713A Attenuator / Switch Driver
11713A Attenuator / Switch Driver Cable (Option 101), 12-pin Viking connector, each end. Standard lengths are 5 feet (-5), 10 feet (-10), or 15 feet (-15). Custom length cables are available upon request (see below).
11713A Attenuator / Switch Driver Cable (Option 201), 12-pin Viking connector, one end; 3 inch bare leads other end. Standard lengths are 5 feet (-5), 10 feet (-10), or 15 feet (-15). Custom length cables are available upon request (see below).
Color coding for easy cable identification is available upon request.
The cost of a custom length cable is $3.00 per foot plus the base price of $108.00. Specify cable part number as 8120-2703-xx-color, where xx is length in feet, and choose from the available label colors: RED, BLUE, YELLOW, GREEN, WHITE, BLACK, or none (leave blank).
Fluke 5725A Amplifier
High Voltage, shielded Interface Cable for the Fluke 5725A Amplifier to 5700A / 5720A Series II Calibrators (standard length approximately 28 inches, 0.71 meter). Old Fluke part number is 859897; new Fluke part number is 842901.
3577A and 3577B Network Analyzers
35677A Test Set Interconnect Cable, 4-pin (standard length 10 inches).
RF Cables for the 8753 Series Network Analyzers - 8753A, 8753B, 8753C, 8753D, and 8753E
Precision 50 Ohm Phase Matched RF Cable Set for the 8753 Network Analyzer to 85046A or 85047A S-Parameter Test Set. These RF cables are usable to 18 GHz and also can be used with the 35677A, 8503A, and 87511A s-parameter test sets. Sold in sets of four and standard length of 7.5 inches (19.0 cm).
8753 Network Analyzer to 85046A or 85047A S-parameter Test Set Interconnect Cable (standard length 18 inches). Also used on 8504A and 8504B Precision Reflectometers, and the 8505A Network Analyzer.
4194 and 4195 Network Analyzers
4194 or 4195 Display to Test Set I/O Interconnect Cable (standard length 18 inches).
4194 or 4195 Display to Test Set 9-Pin Power Interconnect Cable (standard length 12 inches).
4194 or 4195 Display to Test Set BNC Interconnect Cable for high stability oscillator option 001 (standard length 18 inches, doubled shielded, RG142).
4194 or 4195 Display to Test Set BNC Interconnect Cable (standard length 12 inches, doubled shielded, RG142). Four required per test set for 4194, and three required per test set for the 4195.
BNC Interconnect Cable (standard length 24 inches, doubled shielded, RG142).
Source Control Cables
8410B or 8410C Source Control Cable (standard length 72 inches). Connects 8350A, 8350B, 8340B, and 8341B sweep generators to the 8410B or 8410C vector network analyzers.
70000 Series Spectrum Analyzers and Modular System Interface Bus Instruments
MSIB Interconnect Cables, Part Number 70800A (length 0.5 meter), 70800B (length 1.0 meter), 70800C (length 2.0 meter), 70800D (length 6.0 meter).
8558B and 8559A Spectrum Analyzer
Service / Extender Service Cable for Display to RF/IF Plugin (standard length 40 inches).
Rohde & Schwarz FSAS Spectrum Analyzer
W1 RF to Display Interconnect Cable X133, (standard length 12 inches).
W2 RF to Display Interconnect Cable X132, (standard length 10 inches).
8510 Network Analyzer
8510 Network Analyzer "IF to Display"
Interconnect Cable, (standard length 32 inches).
8510 Network Analyzer "Test Set" Interconnect Cable, (standard length 32 inches).
We have new OEM 40 foot, 8510 Network Analyzer "Test Set" interconnect cables. Also part of the Agilent / HP 85301A, 85301B, or 85301C Antenna Measurement Systems. This cable is identical to P/N 08510-60102 except for length and typically is used to connect the 8530A Microwave Receiver to the 8511A or 8511B Test Set of an 85301C Antenna Measurement System. We have a few of these 40 foot, Agilent / HP OEM cables in stock. These cables are new and unused. Note: part number 08510-60104 has been replaced by part number 08530-60004. For reference, standard lenghts of other "Test Set" interconnect cables are as follows: P/N 08510-60106 = 5 ft., P/N 08510-60107 = 10 ft., P/N 08510-60103 = 20 ft., P/N 08510-60104 = 40 ft.
Order P/N 08510-60104-OEM = $1550.00 (sold out)
Custom lengths of our 8510 interconnect cables are available upon request. The cost for the 08510-60101 is $4.50 per foot plus the base price of $115.00. For the 08510-60102, the cost is $35.00 per foot plus the base price of $224.00. For lengths longer than 4 feet, the 08510-60102 cable will consist of 17 conductors plus 7 coax cables in a tinned copper-braided shield with POLYESTER sleeving overall for abrasion resistance.
8505A Network Analyzer System
8505A Network Analyzer "Signal Processor to Frequency Control" Interconnect Cable, (standard length 15 inches).
8505A Network Analyzer to 8501A Storage Normalizer "Labeling" Interconnect Cable (standard length 12 & 18 inches).
8505A Network Analyzer to 8503A S-parameter "Test Set" Interconnect Cable (standard length 18 inches).
8566A, 8566B, 8567A, 8568A and 8568B Series Spectrum Analyzers
RF Interconnect Cable (standard
16 inches and 5 pins). Select five coax pins (-5), four coax pins (-4), or three
coax pins (-3). The 5-pin cable is equivalent to the HP / Agilent OEM cable, part number 86552-60093. The 8568A, 8568B, and 8567A spectrum analyzers use only four of the five coax pin connections. These units require only the 4-pin version of the cable (our part number 85662-60093-4). The 8566A and 8566B spectrum analyzers use only three of the five coax pin connections. These units require only the 3-pin version of the cable (our part number 85662-60093-3).
Bus Interconnect Cable (standard length 22",
"-60094" for standard version or "-60220" for version with tracking generator option that adds SMA connector for access to hswp in/out signal).
BNC Cables, double shielded coax (standard length 4 inches). Usually, three are required for the 8566B, and two are required for the 8568B.
141T Spectrum Analyzer System
Metal connector hoods are used throughout our line of interconnect cables for the 141T Spectrum Analyzer system. The metal connector hoods are customed machined in our shop to be mechanically compatible with the slide latch locking mechanism used on the 141T Spectrum Analyzer system. Metal connector hoods provide a very high degree of RF shielding and are much more durable compared to the original plasitic hoods used by HP.
The extender service cables for the 141T display to the RF/IF plugin units use Amphenol or WPI "ribbon cable" connectors. Due to the lack of suitable connector hoods for these connectors, we custom machine our own hoods to be functionally equivalent the orginal HP cables. We do not include the 180 ohm resistor found on the HP mounting plate. This resistor is not necessary for proper operation and calibration of the plugins using our cables.
HP 8443A/B 100 KHz to 110 MHz Tracking
Generator to 141T/8553B Display Aux. A (standard length 18 inches).
HP 8444A 500 KHz to 1250 MHz Tracking
to 141T/8555A Display Aux. A (standard length 18 inches).
HP 8445B 1.8 GHz to 18 GHz Tracking
to 141T/8555A Display Aux. B (standard length 18 inches).
HP 50 Ohm Termination for 141T/8553B/8555A Aux. A.
Extender Service Cable for RF to IF Plugin Units (standard length 40 inches).
Extender Service Cable for 141T Display to RF/IF Plugin Units (standard length 40 inches).
Extender Service Cable Set Consists of
50 Ohm Termination, RF to IF Service Cable, Display to RF/IF Service Cable (2 each).
HP 8501A Storage Normalizer to HP 8505A
Network Analyzer (standard length 18 inches).
HP 8750A Storage Normalizer (standard length 24 inches).
HP 8750A Storage Normalizer, option 001 w/BNCs allows connection to 141T display (standard length 48 inches).
About Us and Quality -
We specialize in hard to find or obsolete OEM replacement cables for the used test equipment market. Our cables are custom made to order and are designed and professionally made to meet or exceed original manufacturer's specifications. Many of our cables have a higher degree of shielding compared to OEM cables. We use metal connector hoods or back shells on most cables for superior RFI / EMI performance. Occasionally, we can offer new or reconditioned OEM cables when available and repair service on some cables. Email us if you need a repair.
All cables are assembled by us and fully tested before shipment. Certain cables are verified for functionality using manufacturer's original equipment. Our more complex cables are tested on a custom-configured, VXI-based cable tester. We can supply a "Certificate of Compliance" upon request. To maintain our quality, we do not sell parts or kits.
Return to top of page
Ordering and Shipping -
To place an order or to request a quotation and delivery times, email us with the part number, quantity, and shipping address. We normally respond in 24 hours. Prices are in US dollars and do not include shipping cost. Shipments to California addresses are subject to 8.00% sales tax unless you provide us with a current CA resale permit number.
Prices are for standard length cables only. We will be happy to provide a quotation for other lengths and connector or cable configurations.
We ship small orders by USPS Priority Mail to USA destinations. We also can quote FedEx or UPS rate or ship on your account. International orders ship by Priority Mail International or by Express Mail Service (EMS). Please note: Express Mail International provides tracking through customs and delivery. Priority Mail International does not.
For most domestic single cable orders (1 lb or less and 18 inches in length or less), shipping cost is $8.35 for Priority Mail with delivery confirmation. For international orders, multiple cable orders, or other shippers (FedEx or UPS), please email us for shipping cost.
Note: Priority Mail International and Express Mail International are not available to all countries. Shipping costs will be higher to those countries, and an additional charge of US$10 to US$30 will be applied to complete customs forms if required by destination country.
We accept checks drawn on a US bank, wire or telegraphic transfer (T/T), money orders, company purchase orders, and PayPal. Credit cards are accepted only through our merchant account at PayPal. Our PayPal email address is: email@example.com. If paying by credit card, we will gladly forward a PayPal invoice to your email address that you can pay directly and securely. We do not need your credit card information. We are a verified member of PayPal. For international PayPal users, we add 1.5% to total (including shipping). For telegraphic transfers (T/T), a fee of $50 USD will be applied to order to cover our bank's incoming wire fee and so-called "bene-deduct fees".
Contact Information -